The OBDII trouble password of P0335 is recognized as a “hard” code, an interpretation severely detrimental to the procedure of her Accord engine. Much more specifically the DTC P0335 represents a lack of signal indigenous the crankshaft position sensor. The crankshaft position sensor in your Honda Accord informs your ECU that the crankshaft speed and current location.

You are watching: Crankshaft position sensor 2000 honda accord

Without this data, the engine will either no run or run an extremely poorly. Common symptoms are an obstacle starting or the engine may shut turn off randomly, producing a very dangerous instance for not only the driver yet the passengers together well.

Possible causes of OBDII examine engine irradiate P0335Bad or weak batteryBad StarterBad crankshaft place sensorDamaged sensor harness

Today I’ll be reflecting you how to service and also replace her crankshaft place sensor in a 2000 Honda Accord with a F23A1 VTEC SOHC engine.

The part number because that this part is 37840-P0A-A01 for the crankshaft place sensor in your Honda Accord. The can also be found under the component number of 37840-PAA-A01.


*

This How To readjust a Honda Accord Crankshaft position Sensor DIY overview assumes girlfriend have currently removed your driver next engine mount and also supported your engine v a jack. Please examine our just how To adjust a Honda Accord timing Belt guide for an ext details.

Before you start our DIY overview on how To adjust a Honda Accord Crankshaft position Sensor, you must disconnect the negative terminal on your battery. As proclaimed previously, this overview assumes you can raise and also lower your F23 already, i beg your pardon is mandatory when transforming your timing belt.

*

Unplug your 4 pin connector the runs to your crankshaft place sensor in your Honda Accord. Here’s what her pigtail watch like placed to your F23A1. It’s secured through a 10mm bolt that runs with the back of your VTEC SOHC engine.

*

This exploit to her crankshaft position sensor runs v your reduced timing plate, which have to be eliminated to change a Honda Accord Crankshaft place Sensor. In order to execute this, friend must lower your engine if still linked to your chassis, and also remove the crankshaft sheave or harmonic balancer.

This might be an overwhelming if you space working ~ above the ground through hand tools and also don’t have a wait compressor with the ideal air tools. Use a Honda crankshaft wrench, Moroso part number 61805 to appropriately loosen your crankshaft bolt there is no air tools.

*

With the bolt removed, friend should have the ability to wiggle off her crankshaft sheave and set it safely come the side. Do sure eliminate your woodruff an essential and keep that together safe as your pulley.

*

Now you deserve to remove all the 10mm bolts that host your lower timing sheathe in place. Eliminate these unique bolts and also then do your method to the valve cover, girlfriend will need to back off the valve cover bolts the run with to the cylinder head.

Loosen every the valve cover bolts, but do no remove and gently loosen her valve cover. Background the valve covering to enable enough space for your top SOHC VTEC time cover to come off your engine. There room 2 10mm bolts the run through the upper cover to the cylinder head, remove these to ease your upper timing cover.

*

Now slide off your lower timing cover and also pull down to release from your side motor mount. You have to now see your time belt assembly and your F23A1 balance shafts and belts. The crankshaft position sensor in your Honda Accord is situated behind the crank cause plate.

*

You have the right to take among two paths to removing your crankshaft position sensor and also replacing it. You have the right to loosen her timing belt tensioner bolt, the longated bolt located in the center of her tensioner arm. This should enable enough slack as to gently back off your lower crank pulley plate and undo the 10mm bolt that holds the crankshaft position sensor in place.

*

If this is not an alternative for you, check out our how To readjust a Honda Accord timing Belt overview on just how to appropriately time and also remove your F23A1 belts to organization your crankshaft place sensor.

There are several timing point out for your balance obelisk that us recommend girlfriend line approximately TDC before removing her balance column belts.

See more: What Does The M In Ymca Stand For ? What M Stands For In Ymca Crossword Clue

*

Before removing her balance tower belts come reach your crankshaft place sensor, friend will need to double check time marks to ensure your F23a1 is at TDC. Again for much more details inspect our exactly how To DIY guide on an altering the Honda Accord timing belt.

*

Once you have actually replaced your Honda Accord crankshaft place sensor, you can use a scan tool to properly clear her OBDII inspect engine code of P0335. Hope we’ve assisted you learn how To change a Honda Accord Crankshaft place Sensor, if you have any questions please leave us a comment below!