that is this guy?
\"*\"
Join day Apr 2015 place Wisconsin articles 2,291 thanks (Received) 0 Likes (Received) 1 Dislikes (Received) 0Chats10436
\"*\"
in ~ this suggest in time, a most these door dashboard clips room broken. 3 of my 4 doors have damaged clips. Here\"s the connect to the clips ns bought: http://www.amazon.com/gp/product/B00...ilpage_o00_s00 i bought this instead since I\"ve to buy the generic ones most human being buy on Amazon. Those are a tad longer and some human being trim them. The wasn\"t the difficulty for me. My problem was the heads would certainly snap off an extremely easily, and I don\"t slam mine doors. Every clip I changed has currently broken. Therefore I will certainly be giving the ones i posted over a try. And in the pic ~ above Amazon, they\"re white, yet they\"re actually yellow. Not that the matters, however just don\"t it is in alarmed when they aren\"t white.

You are watching: 2004 pontiac grand prix door panel removal


\"*\"
originally Posted by Kaiser Pontiac
\"*\"

Don\"t buy: http://www.amazon.com/gp/product/B00...ilpage_o03_s00Driver\"s door, half of them damaged from normal use and I had actually to take the passenger door off and every solitary one broke on the side.
This thread will certainly pertain to human being wanting to change door dashboard clips, placed in aftermarket speakers, replace a door handle, etc.You will certainly need:
-flat blade screwdriver (a tiny one will occupational the best)-screwdriver with a T27 torx little bit (T25 will work too, a T27 just fits it snugger)-extendable magnet-door panel clips-an expansion of some sort could be essential if your driver is not long enoughHere is the door panel. I will certainly be law the passenger rear door together it to be the just door top top the left side loose.
\"*\"
Here you have the right to see i can quickly pull the door dashboard away type the door because of several broken clips:
\"*\"
Step 1 -
It is probably ideal if friend unhook the battery prior to hand as you have to unclip electric connectors and also your door will certainly remain open for an extended period of time, however isn\"t needed. Take your tiny flat blade screw driver and also stick it between the home window switch, and padded component of the door. Like this:
\"*\"
Gently pry up and also the whole switch will certainly pop up. Elevator the totality thing increase to reveal the electrical connector(s) underneath. Utilizing your small flat blade screwdriver again, pull up top top the tab for this reason you deserve to pull out the connector(s). Collection the window/lock switch aside.
\"*\"
\"*\"
Step 2 -
Behind the manage on the door are 2 little caps. Usage your tiny flat blade screwdriver to wedge it in between the edge of the cap. Room is kind of limited, so smaller the driver the simpler it will be. Pop each that the caps off and collection those aside. Following shine a irradiate up in there and you will watch a torx head screw because that each hole. This screws room to reinforce the handle area for this reason the dashboard doesn\"t bend once someone closes the door or opens up it. Take your T27 or T25 torx bit and also unscrew every screw. Don\"t concern if the screw falls down within the door when you take them out together you will certainly be pulling turn off the whole panel.
\"*\"
\"*\"
Here space those little caps removed:
\"*\"
\"*\"
\"*\"
Step 3 -
After you have those 2 screws removed, it\"s time to begin pulling the door panel off. It\"s most basic to start at the edges whereby your clips are already broken. If girlfriend don\"t have any kind of broken clips, I discovered it easiest to start from the side or the top edge towards the sheet of the door. Grab a host of the panel and start offering it short, quick jolts. Store doing that until it division loose. If lock won\"t budge, the can help to have a trim pry bar and also use it together leverage. Once you have actually a couple of broken loose, it\"s simple to gain the others the end from there. Acquire all the clips broken free, but DON\"T pull THE PANEL turn off YET!
\"*\"
Step 4 -
The reason you don\"t want to just yank the panel turn off yet, is because there is an electrical connector because that the irradiate on the bottom the the door. Unplug the connector the same you go the home window switch from step 1. When that is disconnected, you have the right to now pull the door panel off. In my case, no one of my doors are equipped through the light for the doors so I had actually no connector come remove, but some models have them.
\"*\"
You\"re halfway done!
It\"s not tough at all, simply takes a little bit of patience sometimes. This uses for every door, not simply one. So apply this to every little thing door you desire to remove the panel turn off of.To eliminate the old door dashboard clips, just slide them the end of the door panel and also slide the brand-new ones back in. If some space stuck in the door itself, I simply took a wire snip pliers due to the fact that it\"s angled jaws made it easy to slide in behind the clip. And also pushed ~ above the finish of the pliers together leverage to obtain the old clip out. Functioned every time.
\"*\"
These are the small slots the top of the clips side into.Now because that the reinstallation that the door panels.Step 5 -
With your brand-new clips in and also your panel prepared to it is in installed, reconnect the connector for the door light on the bottom. When that is done, line up the ends of the clips v the feet they go in, and firmly push them into place. Press the panel till it can\"t be propelled in anymore. Carry out this every the method around. Until it\"s firmly in place and can\"t move.Step 6 - With the panel in place, take it the 2 screws and screw them back into place. This is where the magnet comes right into handy. Because the bolt feet aren\"t perfect level, it provides it tricky to gain the screw in there is no it fallout’s down. Put the head the the screw on the magnet and also use the to obtain the the screw started. Once it\"s in a couple threads, traction the magnet off and use the torx little to screw it in the rest of the way. Put the 2 hole covers earlier into place.
\"*\"
This is what ns did. The magnet on the finish of mine screwdriver happened to perfectly fit in the head of screw.
\"*\"
Step 7 -
Take the window switch and plug it ago in. When reinstalling the switch, put the top part in first, and then snap the bottom part in. It\"s less complicated to carry out it this way.
\"*\"
And that\"s it.

See more: What Does Prada Mean In English, Name And Meaning/Definition Of Prada

revolve the crucial to the on position and also hit the lock buttons and home window buttons to make sure they worked. 2nd time i did this, one of my switches didn\"t work. So I just unplugged it and also plugged it back in and it worked.
\"*\"
And there is the door panel every put back together.
\"*\"
\"*\"

#2 Re: how To eliminate Door Panels/Replace Door panel Clips
BillBoost37
\"*\"

Turbo is the means to go.
\"*\"
Join day Jul 2009 location W Spfld posts 26,832 thanks (Received) 52 Likes (Received) 88 Dislikes (Received) 1Chats98246