The timing belt has to be eliminated for an altering the water pump. Here is a guide that will show you what you are in for once doing the job:https://www.barisalcity.org/articles/water-pump-replacementYours will require a time belt as well. I will search for the instructions for that and also get it end to you.Please allow us know what happens.Cheers


You are watching: 2004 chrysler pacifica water pump location

*

*

*

*

*

yet do I have to remove all tension-er's top top the next of the engine to have the ability to get to this? choose power steering alternator etc, to reveal water pump or is it external?


See more: What Does 14K Gf Ppc Mean 14K 8F Ppc, What Does 14K Gf Ppc Mean On Jewelry

Yes, the water pump is inside the time belt cover for this reason you have actually yo eliminate the extrnal contents to gain at it.Removal and installation:Caution:This application is one interference engine. Execute not revolve camshaft or crankshaft once timing belt is removed, or engine damages may occur.Timing belt:Caution:The 3.5L is no a freewheeling engine. Therefore, ease the valve train rocker assemblies prior to servicing the time device.Removal1. Relax fuel mechanism pressure and disconnect negative battery cable. 2. Remove both cylinder head covers and also loosen the rocker arm assemblies. 3. Raise auto on hoist. 4. Remove accessory drive belt and tension-er. 5. Eliminate bolts for strength steering pump and move pump aside. 6. Eliminate right prior wheel and accessory drive belt splash shield. 7. Remove crankshaft damper bolt. Utilizing Puller (1023) and also Insert (9020-R), remove crankshaft damper. See number 1. 8. Remove the lower front time belt cover fasteners. 9. Reduced vehicle. 10. Do the following: assistance engine v a floor jack. remove the air cleaner housing. remove the former engine mount. Disconnect the fuel supply heat at the fuel rail. See number 2. 11. Eliminate the top timing belt cover bolts and remove front timing belt cover. 12. If timing belt is to be reused, note belt running direction. 13. Turn engine clockwise until crankshaft note aligns with the TDC note on the oil pump housing, and also the camshaft sprocket marks room aligned v the point out on the rear cover. See figure 3. 14. Remove the time belt tensioner, and remove time belt. Installation:Caution: If camshafts have moved indigenous the timing marks, always rotate camshaft toward the direction nearest the time marks. Do not revolve camshafts a complete revolution, or damages to valves and/or pistons could result.Caution: index tension-er in the vise the same method it is set up on the engine. This ensures ideal pin orientation once tension-er is installed on the engine.1. Ar tension-er right into a vise and slowly compress the plunger. Check out Fig. 5. Complete bleed down of tension-er need to take about five minutes. 2. When plunger is compressed into the tension-er body, install a pin v the body and also plunger to maintain plunger in place until tension-er is installed. 3. Align the crankshaft sprocket with the TDC mark on oil pump cover. See number 3. 4. Align the camshaft sprockets time reference mark with the mark on the rear cover. See number 3. 5. Download the time belt starting at the crankshaft sprocket walking in a counterclockwise direction. Install the belt roughly the last sprocket. Keep tension ~ above the belt together it is positioned approximately the tension-er pulley. 6. Stop the tension-er pulley versus the belt, install the tension-er right into the housing and also tighten bolts. Each camshaft mark should stay aligned in ~ the behind cover marks. Note:If the camshaft gears have actually been removed, the is only vital to have camshaft gear retaining bolts mounted to a snug torque in ~ this time. 7. As soon as tension-er is in place, pull retaining pen to permit the tension-er to extend to the pulley bracket. 8. Rotate camshaft sprocket two revolutions and also check the time marks ~ above the camshafts and also crankshaft. The marks have to line up within their particular locations. See number 3. If marks perform not line up, repeat procedure. NOTE:If camshaft gears have actually been removed and also timing is correct, counter-hold and also tighten the camshaft gears to last torque specification. 9. Install front timing cover. 10. Perform the following: install the upper engine mount. connect fuel supply heat at fuel rail. See figure 2. download air cleaner housing. 11. Use floor jack come raise vehicle. 12. Install crankshaft damper making use of 5.9" Bolt through Nut (C-4685-C1) and Thrust Bearing (6792), and also Installer (6792-1). See Fig. 6. 13. Install power steering pump fasteners. 14. Install crankshaft damper bolt. 15. Download accessory journey belt tensio-ner. 16. Install accessory drive belt. 17. Download the accessory drive belt splash shield and right front wheel. 18. Lower vehicle. 19. Tighten the rocker arm assemblies and install cylinder head covers. 20. Connect an adverse battery cable. Merry Christmas and a Happy brand-new Year.